I'm having problems with installing my new 600s premium...if anyone has the step-by-step installation instructions, I would appreciate if they can give them to me.

I'm having problems with installing my new 600s premium...if anyone has the step-by-step installation instructions, I would appreciate if they can give them to me.

This is a pretty good c/p..should get you going.
there is a newer 1.06 loader and a new 139 bin file..both here in the file section.


CW600s Premium S/W Upgrade Guide!



Tools Need to update your receiver CW600s Premium Receiver:

1- Null Modem Cable
2- Newest bin Patch “CX_Kround_600Perminum_V1.XX_date.zip" Make sure it is for Premium model.
3- Loading Software "Loader v1.05.zip"

Create a folder on you PCs desktop name "CW_Premium" using Winzip or Winrar unziping program to unzip all files to "CW_Premium" folder.

1) Connect your PC and receiver with twisted RS-232C Null modem cable.

2) Power off the receiver from the back switch.

3) You can load bin file using two methods “boot” Mode and "Standby" Mode. If you want to load the sofware using "Standby" Mode go to #4.
Here how you get into “boot”MODE:
Hold power button on the front of the receiver and turn the power ON from the back of the receiver. You will see a word “boot” on the front LCD screen of the receiver.

4) Turn receiver Off from the back and then ON the receiver; you will see 00:00 now press "POWER" key on front of the receiver panel to make it standby, the LED dot will display “- - : - -“.

5) Start New LoaderV1.05.exe check if the right COM port is selected then select
<Download Main S/W>, press <Open> and select the bin file,“CX_Kround_600Perminum_V1.XX_date.bin" then click <Start>, upgrade will begin.

6) After finishing, the receiver LED will display "-End"
If your experience any problem during the upgrade start over again.

For All of the Featuers available in CW600s Premium Model Please click on this Link :

CW600s Premium Features Guide
mrokarvi

thnx alot for that but summbody programmed it for me...but the thing is after that, the guy said to just blind scan echo3 ut its not wrkin :( can u give me the steps for wat i shud do after i have got the receiver, connected it and got it programmed?

C/P By mrokarvi


Here is a guide to Scan your Satellites
Connect your sat cable to your receiver and hook up your receiver to your TV set. You can

scan Single or Multiple satellites for channels at the same time.
Single Satellite search can be done by going to:
Main Menu -> Installation -> Antenna Setup -> Select the satellite you want to scan for

channels and press “Red” key on your remote
Here are typical Configuration settings for a DSS LNB

Antenna Setting

Satellite name 22 Echostar 6,8 (110W)
Transponder 12224 / V / 20000 / 5 / 6
LNB Freq 11250
LNB Type Normal
22 KHz Off
Diseqc Number LNB1
Legacy SW Off
Motorized System None

You can use “Legacy switch” by changing it to “SW21 Dish1” and changing Diseqc Number back

to NONE.
-After you have done changing the configuration according to your setup press “RED” key on

you remote. It will start scanning all of the channels for that particular satellite.
-You can also access Blind Scan feature from the same screen by pressing “Yellow” key from

your remote.
-If you want to scan only one transponder then press “Blue” key from your remote.

Multiple Satellites Scan
You can scan maximum 4 satellites at a same time using easy tuning feature available in New

OSD
Main Menu -> Installation -> Easy Tuning
Here is a typical setup for multiple satellites using Easy Tuning feature:

Status Satellite name Diseqc LNB Freq

OnEcho 3LNB1 11250
On Echo 6,8LNB2 11250
OnEcho 7LNB3 11250
*** 1,3LNB4 11250


To go from Status to Satellite name scroll down until you see Satellite name field get

highlighted then use right/Left key to change satellite you want scan; now scroll down again

until you get to Diseqc switch setting change it to whatever your switch setting; scroll

down to LNB Frequency setting and change it to appropriate frequency.

After you have finished configuring all Satellites press OK key using right or left press

“Fast Tuning” or “Auto Tuning” system will start scanning all of the satellites one by one.

Enable the Patch

umm ok..i talked to a couple of other ppl n' then started to follow your instructions.

1. i tried to use the settings that u provided me- didn't work

2. did factory default- tried to load the 1.38 nad then after 1.39 bin...that didn't work as its not loading the file...the percentage doesn't increase even after 15 mins

3. before allll this...i tried blindscan, auto everything- nothing worked for echo 3 and echo 7. After all these times, the screen sometimes says "Signal Weak"

4. F1 000..didn't help either as i had enabled my patch from before

What should I do now???

I'm having the same problem...the loader's status bars still reads 0 after 10 or 15 minutes?? I've also tried all the different COM ports...no luck.

I've got all the files and downloads which is great, but why doesn't it work?

Any ideas?

umm ok..i talked to a couple of other ppl n' then started to follow your instructions.

1. i tried to use the settings that u provided me- didn't work

2. did factory default- tried to load the 1.38 nad then after 1.39 bin...that didn't work as its not loading the file...the percentage doesn't increase even after 15 mins

3. before allll this...i tried blindscan, auto everything- nothing worked for echo 3 and echo 7. After all these times, the screen sometimes says "Signal Weak"

4. F1 000..didn't help either as i had enabled my patch from before

What should I do now???

The post above if you noticed was just a C/P copy and paste of a general how to for CaptiveWorks P.

So those setting will not work for you:no:

No one knows what type of dish you have or what type or how many LNBS you have, or if you have any switches involved or what type they might be, or what satellite you are aimed at.?:unsure:

Best thing to do would be to find out what equipment you have and the way it is setup, then post the information here along with what your current settings are in your receiver.

You need to supply that info.:yes:

This way we should be able to get you set.:)