just got hit- serious error- location id 0000001- 4900 rom 3

hit here with atmega and lock 301-13.pulled plug back to normal.just happened.

Around 5:05 EST

Running CEMU on 301.13 - went Error 153.
Rebooted PC and now I only get Ch 101.

Cam hit or TSOP/Flash?

Went down with rom 3 and 10, 153 error. Anyone trying resets right now? Any luck? I will try flashing later and post results. Hopefully not a bad one, UFC is Saturday.

rom10 just got error 153

I have been hit also with loc id 00000001 ERROR 153 since about 4:00pm EST running a 2800 rom 10 i'm still fairly new to this but can I ask if any f you where using checksumblocker?I have heard that nomore64 is up? any truth to that? got to run bbl.

Man i wish my guys would get hit, it's been slow since june. According to others charlie tried to change spending limits and if your blocker didn't allow it, your card got hit!!!!!!

The blocker just prevents the card from taking an update. It doesnt stop the receiver from getting hit. These type ecms sent today are nothing but a pain and a chance for you to mess with the receiver. Just erase the correct sector for your receiver and hook it back up. Takes a couple minutes for the whole process. I have been using the latest nomore64 for a long time and works great to protect the card from updates.

Just got home atmega with ppv's 301.10 @153
Cemu with ppv's 7100 with mic lock hit also hit
everything going again :yes:Probably hit and run seems all good now

Now that the hit is gone would the same fix work?

2700 with atmega got ECM, but 3100 with Atmega still up, same script,

hey Chuck, Thanks for your reply. your exactly right the reason behind my question is perhaps checksum blocker did what it was supposed to and not allow this update thus making the card and ird a "target" for an ecm while on the other hand nomore64 may have let the update through? Jus playing devils advocate here. just wondrering you said you had been running nomore64, did you go down at all since the ecm ?

yeap same fix should work :yes:
still going here wide open

Thanks c-tech

Running a rom10 with dishgods fix been watching it all day seems fine. But i wish something would get hit iam bored!

there is a guy in hashhu called harm45 that predected Tues or Weds that there is/was going to be a ECM before the Superbowl...

I told him to PM me a few Lotto #s :rolleyes:

Just checked my DISH 508's one down with loc ID 000..01 other was fine! I forgot to turn the other 508 off last night and after checking it I powered off, all was fine. Came back and turned it on ... to my surprise loc 000..01! my BEV 508 is OK.

Reloaded P222 software instead of latest P223 and will be testing CSI!

:) :) :)

*** Maybe leaving on the receiver will bypass the ecm unless it gets flagged for an ECM on the next power up? ***

Had one 301.010 go down at 4:20 eastern time and the other at 7:30 eastern. Location Id 00000001. Reflashed the irds and the cards are fine. Was back up in 20 minutes. My bev rom 3 is fine.

yach that was a funny post at hashhu everyone told him off for that one.

I have a 510 mod to 508 with AR105-C installed. I still have lost all my recording. Does anyone have this problem losing their recording?

ECM got my 2800,301.010, and 301.013 yvous emulation. Only the 2800 has the no dialup fix. I have been using rom3 rev 382 hex.

When I got home I lost one of my two 501's and then about one hour later the second reciver went down (153). Erase SA160 waite for dl to complete ... back in business.

Peri :hat:

PS lost my recording too. :grr:

My Rom-3 has been running just fine, but I don't have very much stuff programmed on the card. I don't have any PPV channels programmed on my card. In fact, as stupid as this might sound, I actually have less channels programmed on my test card than I have on my subscribed card.

I got a reboot around 1630 CST so i figured something was up. My AR-105C performed perfectly and other than the 90 seconds or so I was down on the reboot I'm still running fine on my MC1.

If you are using a PVR your recordings are NOT protected. Your IRD won't be hit but you will lose anything you have saved. Oddcircuits is working on a new fix (since December) but it's not out yet.

I suspect Charlie will have another go at us before Sunday. I know I would if I were him. About an hour prior to kickoff.

Hi:
There's not any GCB updated files yet at this time, i think it's not over yet, our uncle Charlie has more surprises for the black sunday. :grr:

Ecm again 3:40 est atmega 301.10 cemu with 7100 wide open ppv's :D

got hit again twice in a day and i got hit yesturday this is bull i think is a attack
for the weekend im going to disconect the satteltite cable of my reciver for the night

did enyone youst get hit

I really dont believe the weekend has much to do with the ECMs coming down. Dish cant stop anyone from hooking up a regular antenae to their TV to watch the Super Bowl on Network TV.

lmao

well if charlie neglected to send ecm's i guess there would not be a charlie
because charlie would be out of business,everyone and there brother would
have a hacked box and watch tv for free ,i think that a lil bit of reading / research is a small price to pay to counter his ecm's :)

got hit again twice in a day and i got hit yesturday this is bull i think is a attack
for the weekend im going to disconect the satteltite cable of my reciver for the night

did enyone youst get hit

Hehe... in the time it takes to reach behind and undo the cable... an extra couple of mins you can jtag the sucker, erase the sector, stream it and watch tv again....

Gives me the chance to dust the shelf where the IRD is sitting :D

Hehe... in the time it takes to reach behind and undo the cable... an extra couple of mins you can jtag the sucker, erase the sector, stream it and watch tv again....

Gives me the chance to dust the shelf where the IRD is sitting :D
bro thats a good one said the same thing to my self"guess i better dust in here " :p

pinto that sounds good but being a newbe of sort i dont know what you mean. would you care to give a step by step?

pinto that sounds good but being a newbe of sort i dont know what you mean. would you care to give a step by step?

Folks have already taken some time to write them up. It may seem daunting at first... but it really isn't. Check out the document at the link below

http://forums.dsstester.com/vbb/showthread.php?t=33183

i was about to think charlie was hitting just rom10 cam id's. but then a model 3000 with a rom3 walked in. i thought charlie had a hard-on for rom10 at first. lmao.