Been using pansat 2500 for over a year with blacklist no problem on just 91. Added a second standard lnb satellite and reloaded bin 235 and channel list for both 91 and 119 (new dish great signal pointed at 119). 91 Works great. But 119 channels say scrambled.
I did in antenna mode chose disq sw 1 for 91 and 2 for 119 as that is what they are plugged into switch.
Is there something I am missing I have to do to turn on E-119 sat?
Thnks

Did you set your disqe switch up right? Every thing has to be perfect to work...Right lnb (Standard on mine....11250 freq) Stuff like that......Check the user guide again...It will work.....

U need to Enable Echo 7 in the menu :yes: then click exit/ then OK to save the changes, U might have to reset the reciever with the power switch in the back

:yes:

Thanks for both replys. First for the Disqe switch. It is generic one I bought with Pansat. It has room for 4 sats. I put 91 on posistion 1, and 119 is plugged into p-2.
Then I went to antenna setup and choose the same coresponding selections and saved. Both are standard 11250 freq and other setting same as before and with guide.
have plugged and unplugged unit. 91 comes in fine. when I tried to scan transponders while on sat 119 on screen it started to find B@V channels on 91. It makes me think that it is not getting tone to disqe switch to change to 119 satellite. Maybe its a low
grade new switch.
TO the second post. I dont see anywhere in online pansat guide or on onscreen menu a choice to Enable Echo 7 in the menu as you advise???
Thanks for any help.
keys should already be in there when using blacklist bin? and 91 is working? am I right?

Thanks for both replys. First for the Disqe switch. It is generic one I bought with Pansat. It has room for 4 sats. I put 91 on posistion 1, and 119 is plugged into p-2.
Then I went to antenna setup and choose the same coresponding selections and saved. Both are standard 11250 freq and other setting same as before and with guide.
have plugged and unplugged unit. 91 comes in fine. when I tried to scan transponders while on sat 119 on screen it started to find B@V channels on 91. It makes me think that it is not getting tone to disqe switch to change to 119 satellite. Maybe its a low
grade new switch.
TO the second post. I dont see anywhere in online pansat guide or on onscreen menu a choice to Enable Echo 7 in the menu as you advise???
Thanks for any help.
keys should already be in there when using blacklist bin? and 91 is working? am I right?

to enable the 119 click menu/installation/setup and scroll down till U find Echo 7 on the list on the left side of the 119 menu page, click it and checkmark it, next on the right side of the menu page turn the DiSEqC switch off and remove it out of line, run the 119 LNB directly to the IF input, still on the right side of the 119 menu page, click exit and then click OK to save the info, go back and check to verify the settings were saved, next at the bottom right of the 119 menu/setting page click on the Satellite Search button, save that, go back and set the DiSEqC switch settings on the Nimiq1/91.0 enabled setting page and also the 119 enabled setup page, hook your DiSEqC switch/cables back and try it, turn your pansat off with the power switch behind the reciever 1 time and try it, Note* 1 thing that might help U is to keep the LNB to DiSEqC switch cables the same length, if the cables are different lengths the switch wont work right

to enable the 119 click menu/installation/setup and scroll down till U find Echo 7 on the list on the left side of the 119 menu page, click it and checkmark it, next on the right side of the menu page turn the DiSEqC switch off and remove it out of line, run the 119 LNB directly to the IF input, still on the right side of the 119 menu page, click exit and then click OK to save the info, go back and check to verify the settings were saved, next at the bottom right of the 119 menu/setting page click on the Satellite Search button, save that, go back and set the DiSEqC switch settings on the Nimiq1/61.5 enabled setting page and also the 119 enabled setup page, hook your DiSEqC switch/cables back and try it, turn your pansat off with the power switch behind the reciever 1 time and try it, Note* 1 thing that might help U is to keep the LNB to DiSEqC switch the same length, it the cables are different lengths the switch wont work right


Thank you so much. Works like a charm now!
Very apprieciated.

Glad to help ^_^

is echo 9 110 ive got 119 working great dut cant get 110

name in the menu :rolleyes:

Echo 3 = 61.5 DishNetwork
Nimiq 1 = 91.0 Bell ExpressView
Nimiq 2 = 82.0 Bell ExpressView
Echo 8.6 = 110 DishNetwork
Echo 7 = 119 DishNetwork

Hi, can any one help me ...

I´m 3 weeks old on this matter, and, every was fine till 1 week ago, first I blank on all channels then I turn of on the back side the ird and all works fine, so after 3 or 4 days again, well by error I press factory setting and press ok, stupid of me, then I can not get to the menu, just shows lenguage screen, a can't get to menu and parental, it just stock on lenguage, then I go to de español language and to the instalation and begining to scan channels, then I can get to the main menu, well it is a mess, I put the new key, then scan channels from 110 & 119 I have 90% quality but I can not see nothing, so What can I do .....