I have a pansat 2500a it was working just fine now I can only watch one sat. this is my set up -echo7 disegc #1 LNB tepy-standard 22KHZ-off LNB power-off positioner-disable. and Echo6,8 same as above but disegc# 2.Echo3 same as above but dusegc #3 ok this is what's happening I can only get sign from disegc#1 I even changed the disegc sw and still thasame problem I don't know if having the disegc sw outside make any difference. I even changed the receiver no difference any ideas.

I have a pansat 2500a it was working just fine now I can only watch one sat. this is my set up -echo7 disegc #1 LNB tepy-standard 22KHZ-off LNB power-off positioner-disable. and Echo6,8 same as above but disegc# 2.Echo3 same as above but dusegc #3 ok this is what's happening I can only get sign from disegc#1 I even changed the disegc sw and still thasame problem I don't know if having the disegc sw outside make any difference. I even changed the receiver no difference any ideas.

The problem is your LNB.
What LNB are you using?? How do you know your pointed at echo6,7, or 8??
Did you tune in to a certain channel?? What sat are you getting with disquc#1??


Oh,..try putting a comma or a period here and there once in a while,.it'll help understand your questions better.

I had it working and I have sign in every one of them I go directly to the receiver and 81 level Quality 99

also post what dishes and LNBs U are using and if U are using a downloaded channel list or having the reciever do a search, post all the info u can think of

but if I had to guess :rolleyes:

I would say that if U are using a downloaded channel list, the channel list switch configuration probably doesnt match your switch configuration


to check/ fix u need to open Gtools, open your channel list and double click on each sat to see/change the switch configuration

or

take all 3 sat cables off your switch, then turn the DiSEqC switces off and check each sat signal, after u verified that your dishes are aligned take the 110 cable and hook it to the reciever, find a 110 channel to verify u have good signal from the 110, next do the same thing to the 119 cable and check a 119 channnel, same for the 61.5, except u will need to scroll to Transponder 5 or 6 to see the signal meter, TP1 TP2 TP3 and TP4 have no signal, next turn the switch configuration back on in the reciever, hook up the 110 find a 110 channel and verify u have a picture, next hook the second 119 cable to the switch and find a 119 channel, if no picture try the 119 cable to the 3rd switch spot or fourth spot, do the same to the 61.5

Note* verify the label on the DiSEqC switch is not on upside down, mine was and it took me a while to figure that 1 out <_<

if it still doesnt work, buy and/or try a different DiSEqC switch


post back :yes:

61.5/110/119. I'm having a little problem. I have a dish 500 w/ separaded lbb pointing 110/119 and a 300 pointing to 61.5 this is my setup 119-disegc #1.110 to disegc #2 and 61.5 to disegc#3 I have good strong signal in each one problem is when I turn to 61.5 channels I loose signal in 11o and 119 AND TO GET THEM BACK I have to reset the receiver I don't know if the problem is that the 300 dish is like 35 feet away from the 500 dish. olso I have a download channel list. any help

61.5/110/119. I'm having a little problem. I have a dish 500 w/ separaded lbb pointing 110/119 and a 300 pointing to 61.5 this is my setup 119-disegc #1.110 to disegc #2 and 61.5 to disegc#3 I have good strong signal in each one problem is when I turn to 61.5 channels I loose signal in 11o and 119 AND TO GET THEM BACK I have to reset the receiver I don't know if the problem is that the 300 dish is like 35 feet away from the 500 dish. olso I have a download channel list. any help


My guess is that your flash is causing the the nag.
If you know how to reflash...go ahead and try an updated flash.