Can someone with a modded nexus t-911[orange] Please tell me how to flash and then to run. all it has is 6 dip switches. thanks :blink:

your is not in the list but try 1 and 6 to flash
=================
No-switch loaders
=================
T7
T6-mini
Aftershok Plus
X-loader
Easybuy2000 Hu Loader
DL Detonater
Scorpion Pro Plus
Black Widow
Mikobu II


=================
Acidlabs Glitcher
=================
Up is off
Down is ON
Only one switch is on at a time, most applications work with all 4 off. Advanced procesers require 3 ON and atmel pins 13 and 13 shorted together.
D1 ON = 1/2 clock speed inverse phase glitching
D2 ON = clock speed normal phase glitching
D3 ON = clock speed inverse phase glitching
D4 ON = 1/2 clock speed normal phase glitching

==========
Annihilator II
==========

Pin 1 and 2 are not used on the unit.

Flashing: 3 on 4 thru 8 off
Lode Mode: 3-4 on, and only one clock switch of your choice.(Most succuess 6 on)
Unloop Mode: 3 on, 4 thru 8 off
Phoenix Mode: ALL OFF
For HU testing unplug, switch 3 on, everything else off.
Flash HU code.
Put switches 3,4 and either five or six
(both work but choose one at a time only)
Power on and your ready.

======================
Aftershok Original (?)
======================
H - Unlooper Mode: switch 1 and 5 down, the rest up
HU-Loader Setting 1: switch 2 and 5 down, the rest up
HU-Loader Setting 2: switch 2 and 4 down, the rest up
Phoenix Mode: switch 5 down, the rest up. Card must be in when turning unit on. Both LED's will light up.

============
Aftershok II
============
H-Unlooper Mode, 1 & 5 ON - 2,3,4 & 6 OFF (also use this set-up for inline flashing Atmel)
HU-Loader Mode, 2 & 5 ON - 1,3,4,6 OFF (if HU-card won't glitch, try 4 ON 5 OFF)
Phoenix Programmer Mode, 5 ON - 1,2,3,4 & 6 OFF (for running in programmer mode un-plug power, place card in slot, and plug power. Note both leds must
be ON for Programmer Mode)


================
Aftershok 4 in 1
================
HU Loader Mode 2 & 5 ON
H Unlooper Mode 1 & 5 ON
H ISO Programmer Mode (Valid-H) All OFF (Up) Insert H Card before applying power. Both lights should come on.
H Phoenix Programmer Mode (BS-H) All OFF (Up) Insert H Card before applying power. Both lights should come on.
ATMEL Programming Mode 1 & 5 ON (Down)

==========
Atomic PUT
==========
for flashing
switch 1,5 on the rest off

for hu programing
switch 2,5 on the rest off

---------------
Variation 1:
---------------

For the black case Atomic PUT:
flash mode: 6 on
unlooper: 1 & 5 on
pheonix: 1 & 5 on
loader: 2 & 5 on

For the clear case Atomic PUT:
flash mode: 1 & 5 on
unlooper: 1 & 5 on
pheonix: 5 on
loader: 2 & 5 on

=============================
Barracuda Glitcher (original)
=============================
All 4 OFF to flash #3 to ON for regular use

================
Black Knight T6
================

Flash - 2,6 on
Unlooper - 5 on
Loader - 2,5 on
POhoenix - all off

=============================
Cobra Venom/Vector Fusion (?)
=============================
Flash 2&6 up
P3 2&5 up
P2 2 up
P 5 up

==========
Detonator UL
==========
Normal operation, all dips DOWN

=======================
InTek SCRT programer/unlooper
=======================
J6 controls the loader glitch options. When a jumper is installed on the #1 pair of jumper pins (default setting), this is the equivalent of connecting (shorting) pins 13 and 14 of the Atmel chip to one another. When jumper is installed on the #2 pair of jumper pins, gated clock pulses are supplied to pin 14 of the Atmel chip. If necessary, it is permissible to install jumpers on both the #1 and #2 pin pairs of J6.

J7 controls the clock glitch selection.By default, the #2 set of jumper pins have a jumper installed on them
Pair #1 - 18.432 MHz gate (normal)
Pair #2 – 9.216 MHz gate (normal) – default setting
Pair #3 - 9.216 MHz gate (inverted)
Pair #4 – 18.432 MHz gate (inverted)


==============
Kpyro Unlooper
==============
SW1: - CLK/2
SW2: + CLK
SW3: - CLK
SW4: -CLK/2

==============
ISO Wave PS2 Plus
==============
H Card (Virgin) 1 ON 2 ON 3 OFF 4 ON 5 OFF 6 OFF

B/S H Card (Black Sunday) 1 ON 2 ON 3 ON 4 OFF 5 OFF 6 OFF

Dish Network 1 OFF 2 OFF 3 OFF 4 OFF 5 ON 6 ON

=======
ISO WAVE
=======
H Card (Virgin) 1 ON 2 ON 3 OFF 4 ON 5 OFF 6 OFF
B/S H Card (Black Sunday) 1 ON 2 ON 3 ON 4 OFF 5 OFF 6 OFF
Dish Network 1 OFF 2 OFF 3 OFF 4 OFF 5 ON 6 ON

========
Pro Loader
========
1 & 5 ON - Flashing and H Unlooping
5 ON - Phoenix Programmer Mode/ H card
2 & 5 ON - HU Loading
2 & 4 ON - HU Loading (stubborn cards)

============
Omega Loader
============
2 on for all flash/programming functions

The switch on the back is for switching between echo and dtv.

=================
Scorpion Unlooper
=================
All switches OFF = Software controlled
SW1 = Fastest for easy repairs (CLK/2 + Slope(9Mhz))
SW2 = Cruising Speed for easy repairs (18Mhz CLK +Slope)
SW3 = Slower glitch for hard to repair cards (18Mhz - Slope)
SW4 = Slowest timing glitch for stubborn cards (CLK/2 - Slope (9Mhz))

Only use 1 switch on at any one time..

================
Stinger Unlooper
================
SW1: - CLK/
SW2: + CLK/2
SW3: + CLK
SW4: - CLK

=====================
T5 TERMINATOR TYPHOON
=====================

The UNLOOPER MODE comes already comes programmed with SU2 code. To change the Unlooper code from SU2 to whatever code you want, make sure that switch 5 is in UNLOOPER MODE (#5 switch UP) then use the FLASH utility (or any available flash utility) to flash the UNLOOPER MODE to any of the current available codes.

The LOADER MODE comes without any code- you must flash the unit yourself, which only takes a few seconds. To program the code in to the LOADER MODE make sure that switch 5 is in LOADER MODE (#5 switch Down) then use the FLASH utility (or any available flash utility). After you flash your Terminator T5 Typhoon you will have a fully functioning Loader.

HOW TO OPERATE THE T5 IN UNLOOPER MODE

To operate in UNLOOPER MODE move switch #5 to the UP position. The software that the Unlooper will work with depends on the code you used to flash the UNLOOPER MODE. The Terminator T5 Typhoon comes flashed with the UNLOOPER MODE flashed to SU2.

HOW TO OPERATE THE T5 IN LOADER MODE

To operate in LOADER MODE move switch #5 to the DOWN position. This enables the micro processor chips on the bottom side to enter the glitch mode. The software that the LOADER MODE will work with depends on the code you used to flash the LOADER MODE. The Terminator T5 Typhoon will work perfectly with all currently available "PRO" type software.

T5 SWITCH SETTINGS

Between the power input and the place where you attach the serial cable you will notice a blue box with 5 white switches on it. These are the switches you need to use to select which mode you want to use, as well as to fine tune the glitching. For best results it is suggested that you normally set switch #3 to the DOWN position to get the most out of your Terminator T5 Typhoon. This allows the clock to operate at 18.432 MHz, and makes sure that the glitches are started in relation to the rising edge of the system clock- in other words- FULL TILT MODE! Feel free to try your Terminator T5 Typhoon in any other clock setting, but ONLY HAVE ONE OF THE SWITCHES DOWN AT A TIME SWITCH #1 OR #2 OR #3 OR #4 DOWN @ A TIME.


Switch # 1 is half clock negative slope
Switch # 2 is half clock positive slope
Switch # 3 is full clock positive slope
Switch # 4 is full clock negative slope
Switch # 5 toggles between UNLOOPER MODE and LOADER MODE. (UP for UNLOOPER, DOWN for LOADER)


========================
T5 Typhoon Terminator II
========================
Dip Switch Settings:

Phoenix Programmer Mode
3 On 1,2,4,5,6 Off
H Unlooper Mode - Flash Mode
3, 6 On 1,2,4,5 Off
P3 Loader Mode - Flash Mode
3,5,6 On 1,2,4 Off

In other words, flash with 3,5,6 on.. leave that way for Hu cards..
switch to 3 on 1,2,4,5,6 off for H cards...


======
T6 IVQ2
======

Flash on off off off off off

H Unlooper on off off off on off

Phoenix off off off off on off

HU Loader off on off off on off

Dish Loader off off off off off off


=======
T6 Wave
=======
T-6 1 2 3 4 5 6
DirectTV (Virgin) ON ON OFF ON OFF OFF
DirectTV (BS) ON ON ON OFF OFF OFF
Dish Network OFF OFF OFF OFF ON ON


T6 WAVE-Atmel In-Line Flash


T-6
1 2 3 4 5 6
DirectTV (Virgin) ON ON OFF ON OFF OFF
DirectTV (BS) ON ON ON OFF OFF OFF
Dish Network OFF OFF OFF OFF ON ON


T6 WAVE-Atmel In-Line Flash

1 2 3 4 5 6 KK Flash software
Atmel Flash ON OFF OFF OFF ON OFF Choose below
H-Card (Virgin) ON OFF OFF OFF ON OFF WildThingX+
H-Card (BS) ON OFF OFF OFF ON OFF SU2BS01
HU ON OFF OFF OFF ON OFF TritonHU


T6 WAVE-Image Loading

1 2 3 4 5 6 UNLOOP/CLEAN LOAD
H-Card (Virgin) ON OFF OFF OFF ON OFF TurboUnloop 1.1 TurboUnloop 1.1
H-Card (BS) ON OFF OFF OFF ON OFF TurboUnloop 1.1 TurboUnloop 1.1
HU Setting 1 OFF ON OFF OFF ON OFF Extreme HU 1.6 Extreme HU 1.6
HU Setting 2 OFF ON OFF ON OFF OFF Extreme HU 1.6 Extreme HU 1.6

Note:
1. For HU, If setting 1 doesn¡¦t work, try setting 2.
2. For H-card, in Winexplorer 4.6, set Configure„³ Program Parameters„³ Quick Settings „³ Unlooper
Atmel Flash ON OFF OFF OFF ON OFF Choose below
H-Card (Virgin) ON OFF OFF OFF ON OFF WildThingX+
H-Card (BS) ON OFF OFF OFF ON OFF SU2BS01
HU ON OFF OFF OFF ON OFF TritonHU


T6 WAVE-Image Loading

1 2 3 4 5 6 UNLOOP/CLEAN LOAD
H-Card (Virgin) ON OFF OFF OFF ON OFF TurboUnloop 1.1 TurboUnloop 1.1
H-Card (BS) ON OFF OFF OFF ON OFF TurboUnloop 1.1 TurboUnloop 1.1
HU Setting 1 OFF ON OFF OFF ON OFF Extreme HU 1.6 Extreme HU 1.6
HU Setting 2 OFF ON OFF ON OFF OFF Extreme HU 1.6 Extreme HU 1.6

Note:
1. For HU, If setting 1 doesn¡¦t work, try setting 2.
2. For H-card, in Winexplorer 4.6, set Configure„³ Program Parameters„³ Quick Settings „³ Unlooper


====
T911
====
Unlooper for H or BS H cards 1-5 on
Phoenix mode 5 on (card must be in T911 before you connect the power to the unit. Both lights MUST be on!)
Hu mode 2-5 or 2-4 on
Flash Mode 1-5 on

============================================
Ulitmate 3in1 Programmer/Unlooper/Loader (Shanty)
============================================
H-Unlooper Mode: Switch 1 and 5 ON, 2,3,4 and 6 OFF. This setup is also for flashing Atmel chips.
Phoenix Programmer Mode: Switch 5 ON, 1,2,3,4 and 6 OFF. Unplug power, place a card in slot, then plug power. Both lights should come on.
Hu-Loader Mode. Switch 2 and 5 ON, 1,3,4, and 6 OFF. If the card won’t glitch, try 4 ON, 1,2,3,5 and 6 OFF, or 1, 4 and 5 ON 2, 3, 6 OFF.

============================
TRI-Mode Programmer/Unlooper/Loader
============================
H-Unlooper Mode : Switch 1 and 5 ON, 2,3,4 and 6 OFF. This setup is also for flashing Atmel chips.
Phoenix Programmer Mode : Switch 5 ON, 1,2,3,4 and 6 OFF. Unplug power, place a card in slot, then plug power. Both lights should come on.
Hu-Loader Mode. Switch 2 and 5 ON, 1,3,4, and 6 OFF. If the card won't glitch, try 2& 4 ON, 1,3,5 and 6 OFF, or 1, 4 and 5 ON 2, 3, 6 OFF.

====================
Ultimate Solution All-In-One
====================
hunlooper-flash mode-Phoenix 1-5 on
hu loader 2-5 on


===========
WHiZ Loader
===========
2 up and 1 3 4 down for everything

Thanks for the reply ctech. I guess i'll have to contact topshelf. These settings won't work. :no: