Many testers have this problem, after the Tsop flash, and the IRD doesn't power up, here is something you can try.

Requirements:JKeys 2.9

For 3100 IRD
1) Plug Jtag in, then IRD
2) Open Jkey.
3) In the action menu erase Flash start location (1FC00000) (U23).
4) Unplug receiver then plug in again and restart JKey.
5) Select the U23 bin file you want on there. Start address (1FC00000), Length (1FCD5555).
6) In Action menu choose Program Flash. (It may say "Slow mode"; ignore)
7) You will eventually get an Error.
8) Close Jkey. and unplug IRD
9) Plug in IRD and the light should flash if done correctly. You have now woken up your IRD.
10) Open JKeys and erase Flash U23 full. WITHOUT unplugging the IRD, put your U23 software back on.
11) Close JKeys unplug receiver
12) Plug receiver in and start JKeys. It should read your BKeys, IRD # and the IRD light should blink again.
13) Now erase Flash U22 full. WITHOUT unplugging the IRD, put your U22 software back on.
14) Now close JKeys, unplug IRD, plug IRD back in. You should be fixed and the light on your IRD will stay ON.

Watch TV.!

===============================================

For 2700/2800 IRD

If your 2700/2800 does not power up (no green light) after flashing, follow these steps:
Ground pad #1 to the chassis of IRD. Hook up JTAG, plug IRD into wall, bring up JKeys and then click on "Flash Programming". Do not click on "OK" yet, instead, unplug IRD for a few seconds, then plug it back in. Count to 3 and then click on "OK". Now try re-erasing flash and rewriting TSOP bin to IRD.

Yes...this works for the 2700...thanks Mas for bringing my ird back to life a few days ago.... :D

Yes...this works for the 2700...thanks Mas for bringing my ird back to life a few days ago.... :D


No problem :beer: helping you just like helping myself learnning too :hat: as we both from the DTV side

Ground pad #1 to the chassis of IRD

How do I do that?

Ground pad #1 to the chassis of IRD

How do I do that?

Solder a wire a pad #1, then gound to the ird box.

OK, I've got to bring this thread back up. My 2800 was ECM'ed and the sector erase and update thing didn't work. So, I had a saved TSOP (non-ECM'ed) to write back. I went in and did a full erase (5 times) and wrote my clean TSOP back. Plugged it in and no green light, no picture. Tried Mas' method above at least three times and still nothing.

The only thing I'm wanting to make sure of (cuz I think I'm doing it right but not absolutely sure) is about the grounding to Pad#1.

I've got the alligator clip on my Jtag which I connect to the grounding post on the bottom of the IRD for doing my Jtagging. When you say to ground Pad#1 to the IRD chassis, are you saying to connect a wire from Pad#1 to another grounding point on the chassis and that the one that is connected to the Jtag is not the one you are referring to? Just want to be clear.

Thanks!

I went ahead and soldered a wire from Pad 1 to another screw post on the chassis, tried all of the above methods three times again and my 2800 is still snoozing.

On the other hand, I can run Jkeys and it shows my IRD, the newly flashed TSOP (with boxkeys and the old software version which is 766P) and everything else. All seems fine except that I cannot get the receiver to turn on.

Is there anything else to try? Blown fuses? Different plugging/unplugging? Witchcraft? Something that will keep me from buying another box.

Thanks!

rallen88

Have you get the receiver fix?

Someone PM me with the same so, I bring the post to the top again, and move the Faq forums

Nope, never did. It's collecting dust on a shelf but I haven't really messed with it in a while. Sort of waiting for anything new to try with it since everything I've tried so far has failed to wake it up...

Nope, never did. It's collecting dust on a shelf but I haven't really messed with it in a while. Sort of waiting for anything new to try with it since everything I've tried so far has failed to wake it up...


Maybe just try with the new TSOP

Have you tried a junk yard fix on the 2700? Ground pads sb39 and sb40 together with the power on for about ten seconds, you will see the power pight blink several times, hook the ird up to the dish and let it sit for half an hour.

I may give that a shot just to have something to fiddle with since Charlie seems to be leaving us alone otherwise...

I've tried the new TSOP idea Mas, after a certain point, it stopped even showing what software ID etc that I had on the box. I may try newbie's junkyard fix idea though...

Will keep ya posted.

I may give that a shot just to have something to fiddle with since Charlie seems to be leaving us alone otherwise...

I've tried the new TSOP idea Mas, after a certain point, it stopped even showing what software ID etc that I had on the box. I may try newbie's junkyard fix idea though...

Will keep ya posted.


The Junk Yard Fix will not fix the problem you have, You have to reflsah with the new tsop

Many testers have this problem, after the Tsop flash, and the IRD doesn't power up, here is something you can try.

Requirements:JKeys 2.9

For 3100 IRD
1) Plug Jtag in, then IRD
2) Open Jkey.
3) In the action menu erase Flash start location (1FC00000) (U23).
4) Unplug receiver then plug in again and restart JKey.
5) Select the U23 bin file you want on there. Start address (1FC00000), Length (1FCD5555).
6) In Action menu choose Program Flash. (It may say "Slow mode"; ignore)
7) You will eventually get an Error.
8) Close Wall and unplug IRD
9) Plug in IRD and the light should flash if done correctly. You have now woken up your IRD.
10) Open JKeys and erase Flash U23 full. WITHOUT unplugging the IRD, put your U23 software back on.
11) Close JKeys unplug receiver
12) Plug receiver in and start JKeys. It should read your BKeys, IRD # and the IRD light should blink again.
13) Now erase Flash U22 full. WITHOUT unplugging the IRD, put your U22 software back on.
14) Now close JKeys, unplug IRD, plug IRD back in. You should be fixed and the light on your IRD will stay ON.

Watch TV.!

===============================================

For 2700 IRD

If your 2700 does not power up (no green light) after flashing, follow these steps:
Ground pad #1 to the chassis of IRD. Hook up JTAG, plug IRD into wall, bring up JKeys and then click on "Flash Programming". Do not click on "OK" yet, instead, unplug IRD for a few seconds, then plug it back in. Count to 3 and then click on "OK". Now try re-erasing flash and rewriting TSOP bin to IRD.

hi mas.................. i tried to do wat you said in here about 2700
here is wat i did hooked up JTAG , pluged ird in the wall , brought up Jkey ,
stoped here, cant do the flash bc it wont detect the ird and ird never went to power up. untill the jkey detects it i cant flash, and until it powers i guess it wont detect either...........................
help please

Oh, I didn't see that you did a full erase. You have to get the correct build config tsop and put it onto the ird. that is the only way that you are going to bring that thing back to life.

[QUOTE=newbie09]Oh, I didn't see that you did a full erase. You have to get the correct build config tsop and put it onto the ird. that is the only way that you are going to bring that thing back to life.[/QUO

how can i do it ,
the ird wont do anything its like dead bone,
i tryed to put in dish net stream but no luck

After flashing tsop on 2800, no power. I had backed up the original tsop before I tinkered with it, so I tried loading the original tsop using the above procedure. No luck--still no power. Jkeys is reading from the ird though, and everything looks like it should. Don't know why it won't power on. Suggestions?

After flashing tsop on 2800, no power. I had backed up the original tsop before I tinkered with it, so I tried loading the original tsop using the above procedure. No luck--still no power. Jkeys is reading from the ird though, and everything looks like it should. Don't know why it won't power on. Suggestions?


Try with another 2800 same built tsop, verify the tsop built from IRD sticker, make sure you got the correct tsop built.

Re-flashed and completely disconnected jtag and ird came back on. One problem solved . . .

does the 3100 instructions work for the 301 or are there a couple different steps...i follow steps, get my two light flashes where indicated , when i attempt the final u22 install i stiill get no power on ird...any help welcomed

srv

does the 3100 instructions work for the 301 or are there a couple different steps...i follow steps, get my two light flashes where indicated , when i attempt the final u22 install i stiill get no power on ird...any help welcomed

srv

http://forums.dsstester.com/vbb/showthread.php?t=29748

thanks for the help...one ting i found out trying to revive my 301 was for some reason i couldnt reflash using win xp...i fired up other computer with win98 and the tsops took on the first try...just passing the info along

srv

thanks for the help...one ting i found out trying to revive my 301 was for some reason i couldnt reflash using win xp...i fired up other computer with win98 and the tsops took on the first try...just passing the info along

srv


Glad you get it working :beer: :beer:

How 'bout a 4700 revival?? Anybody got info on that one?No power light here can read in Jtags tho

How 'bout a 4700 revival?? Anybody got info on that one?No power light here can read in Jtags tho


try reflash the good or virgin tsop back to your IRD

Ok Mas u R da man around here this is my problem I have a 4700 that I saved tsop from it which is a cchd build yet when I saved tsop it read ccha..anyhow I loaded the 4900 flash for atmega which at 1st I didnt know that u can only load that flash for atmega and not rom10. This is what happend the ird worked np until I came home next day then there was black screen and ird was stucking on aquring signal.Since then Ive tried everything to get it going including loading original tsop, and nodda...Got another 4700 from Dads place and saved mem same way but beforeI erased tsop,I erased sa30 and it took update. then loaded 4900 ccga file from here and done up rom10 card and 2nd ird going last nite and this morn will see after when I get home tonite..So I loaded same tsop from 2nd ird and 1 4700 is still stuck on aquirng signal???? weird I hope the 2nd 4700 doesnt go down same way,its like dish sent some sort of update to kill it????? Been going nuts trying to get 1st 4700 going ready to try this remedy u got here but will it work for 4700???? I get lites though but it wont take update even if I erase sa30 justs sits there??? Help Help thanks

Ok Mas u R da man around here this is my problem I have a 4700 that I saved tsop from it which is a cchd build yet when I saved tsop it read ccha..anyhow I loaded the 4900 flash for atmega which at 1st I didnt know that u can only load that flash for atmega and not rom10. This is what happend the ird worked np until I came home next day then there was black screen and ird was stucking on aquring signal.Since then Ive tried everything to get it going including loading original tsop, and nodda...Got another 4700 from Dads place and saved mem same way but beforeI erased tsop,I erased sa30 and it took update. then loaded 4900 ccga file from here and done up rom10 card and 2nd ird going last nite and this morn will see after when I get home tonite..So I loaded same tsop from 2nd ird and 1 4700 is still stuck on aquirng signal???? weird I hope the 2nd 4700 doesnt go down same way,its like dish sent some sort of update to kill it????? Been going nuts trying to get 1st 4700 going ready to try this remedy u got here but will it work for 4700???? I get lites though but it wont take update even if I erase sa30 justs sits there??? Help Help thanks

You have to verify the tsop build from inside the IRD itself, to make sure you get the right config build for your IRD. You can not flash ccga to your IRD because you IRD have cchd(ccha) build

Yes sir I realize that I did change the build config of the ccga file here to ccha to match my ird.Well I just got in and I tried 2nd 4700 ird and its working.So my conclusion from this is that the atmega file loaded on atmega,along with the 4900 flash for atmega did something to my 1st ird since it worked for a nite and until I got in at nite and I turned it on to a black screen and since then I havent been able to get it to work...Its stuck on aquring signal no matter what I do???

Yes sir I realize that I did change the build config of the ccga file here to ccha to match my ird.Well I just got in and I tried 2nd 4700 ird and its working.So my conclusion from this is that the atmega file loaded on atmega,along with the 4900 flash for atmega did something to my 1st ird since it worked for a nite and until I got in at nite and I turned it on to a black screen and since then I havent been able to get it to work...Its stuck on aquring signal no matter what I do???


Did you change the BUILD DATA also to match your original TSOP not just the BUILD CONFIGERATION ? if not give that a try.

Yeah I did but all u need to change is the build #'s and the data changes automaticly when u hit fix crc box

Hello everyone, I read about Jtag and how to get it working. My Lifetime Ultra doesnt work, power doesnt come on. Where can I get the stuff I need to make a Jtag cable? Do I ask for it by specific name? I would greatly appreciated anyone's assistance.

thank you all in advance

Hello everyone, I read about Jtag and how to get it working. My Lifetime Ultra doesnt work, power doesnt come on. Where can I get the stuff I need to make a Jtag cable? Do I ask for it by specific name? I would greatly appreciated anyone's assistance.

thank you all in advance

Yjis is Dishnet receiver, upu have to look in FTA Forums

For 2700 IRD

If your 2700 does not power up (no green light) after flashing, follow these steps:
Ground pad #1 to the chassis of IRD. Hook up JTAG, plug IRD into wall, bring up JKeys and then click on "Flash Programming". Do not click on "OK" yet, instead, unplug IRD for a few seconds, then plug it back in. Count to 3 and then click on "OK". Now try re-erasing flash and rewriting TSOP bin to IRD.
Where can i find ground pad #1?:unsure: <_<

I can do programming ,erase,with JKeys but my ird light does not turn on.I tried to full erase many times and write a new tsop but still doesnt turn on the power light.(I did everything that is written above but still no go,btw my ird is 2700 cata)

For 2700 IRD


Where can i find ground pad #1?:unsure: <_<

I can do programming ,erase,with JKeys but my ird light does not turn on.I tried to full erase many times and write a new tsop but still doesnt turn on the power light.(I did everything that is written above but still no go,btw my ird is 2700 cata)


If the Jtag can detected IRD infor that fine, what you need is a good or Virgin TSOP and EEPROM to flash to your IRD.

Do we have a fix for 301.013? I erased the flash, and now that thing does not even power up.

For 3100 IRD
1) Plug Jtag in, then IRD
2) Open Jkey.
3) In the action menu erase Flash start location (1FC00000) (U23).
4) Unplug receiver then plug in again and restart JKey.
5) Select the U23 bin file you want on there. Start address (1FC00000), Length (1FCD5555).
6) In Action menu choose Program Flash. (It may say "Slow mode"; ignore)
7) You will eventually get an Error.
8) Close Wall and unplug IRD
9) Plug in IRD and the light should flash if done correctly. You have now woken up your IRD.
10) Open JKeys and erase Flash U23 full. WITHOUT unplugging the IRD, put your U23 software back on.
11) Close JKeys unplug receiver
12) Plug receiver in and start JKeys. It should read your BKeys, IRD # and the IRD light should blink again.
13) Now erase Flash U22 full. WITHOUT unplugging the IRD, put your U22 software back on.
14) Now close JKeys, unplug IRD, plug IRD back in. You should be fixed and the light on your IRD will stay ON.



My question is about step 8. You mentioned that you use jkeys for the program, but in step 8 you say close wall. Are you refering to the program wall? Please clarify.

Thanx

My question is about step 8. You mentioned that you use jkeys for the program, but in step 8 you say close wall. Are you refering to the program wall? Please clarify.

Thanx

Thank you for pointed out the mistake. You can you either Jkey or Wall to flash the IRD.

Thanx mas521ca

Got 2 2700s back up and running.

Not quite as licky with the 3100. Jkeys will not detect the type and all buttons greyed out.

Not able to access drop down menu either.

I did try to trick it by jtagging one of the 2700s and when I was able to access the menus I selected 3100 and tried but it kept giving me errors.

Well; unless you have another trick up your sleeve I guess I'll have to scrap it.

hey guys im new to this, and my 2700a pansat wont come on.

there is just the side scrolling green bar that goes left to right. the power wont come on. what do I need to fix this.

please help

you have the knight rider syndrome`,you either loaded a bad file,or the wrong one,go back and check latest files and reload,if not you may have to load fac.bin then load the currant one...

hey guys im new to this, and my 2700a pansat wont come on.

there is just the side scrolling green bar that goes left to right. the power wont come on. what do I need to fix this.

please help

you have the knight rider syndrome`,you either loaded a bad file,or the wrong one,go back and check latest files and reload,if not you may have to load fac.bin then load the currant one...

This one is for DN receiver 2700, not Pansat 2700A/E.

Hi, will the methods that you have posted work on a 3800? Thanks

Hi, I have exactly the same problem. Did you ever get it to turn on? Thanks

you think this will work for the dead viewsat?

have anyone found a fix for the dead viewsat?

i have the pansat clone and was loading yhe new 1=3 falsh when it feroxe i turned it off then back on lights would not go on but i know it still works because the inside still gets warm what do i need

I think this is enough .....
I do agree with you. Those are the most effective way

Keep it to yourself bod. Pay for space to advertise your s**t.
Post reported and neg reped.

Keep it to yourself bod. Pay for space to advertise your s**t.
Post reported and neg reped.
Dont forget the paper work for neg repping him into the dog house. hahaha

Dont forget the paper work for neg repping him into the dog house. hahaha

Otherwise Papa will get mad... !!!!:lol::wow::hat:

Banned no paperwork necessary now :D

Banned no paperwork necessary now :D
Thanks, Chuck.
.....and to be honnest, I didn't know how to go about this one. I was expecting 'ITS ME" to beat me to it. ( just joking):D

I have Sony SAT-B3 that do not respond to the power button. :huh: both fuses are good, and +5V supply is spot-on. I'm a newbie, so, please be gentle.... <_< any advice ? Any recommendations for communicating with the box to see if it is only partially insane ? Schematics ? :beer:

I have a 2700 i made the jtag 25 pin parallel port which is lpt1 but cant find anywhere the jkeys that will recognized that port

The receiver doesnt have the 9 pin only the cut in the botton for the jtag hardwire.
any link for the keys will help please