Ok, I wanted to start a thread for PowerSync Users Unlocking Rom 103 using the new RM1_A = Rom Master version 1A Unlocking App by Reberserf. Please post your results here with the following information:

Cam Rev

Switch Setting
Ohm Setting

Rom Master *USER SETTINGS*
ComPort=
CommDelay=
CommLogging=
ImageBackup=
ExitPrompt=


I'll start off by posting a couple of success settings that I've had:

Rom 103 Rev 385 icam

Switch 1
Ohms 185

Rom Master *USER SETTINGS*
ComPort=1
CommDelay=2
CommLogging=ON
ImageBackup=ON
ExitPrompt=ON

Parameters-> Delay:03D5 VCC:002B Glitch Type:B5/09
Elapsed: 00:02:59

---------------Rst24------------------------------Rst15--+FF---------
------Rst3C !!!!!!!

******* Good response received! *********
55
===========================================
55 was hit at: Delay:03D5 VCC:003D GlitchType:B5/0A
Elapsed: 00:03:03
VCC Resolution: 0.5
Delay Range: 03D3 to 03D8
********************************
* Rom103, Rev385 CAM OPEN!

__________________________________________________ _______________

Rom 103 Rev 386 icam

Switch 1
Ohms 210

Rom Master *USER SETTINGS*
ComPort=1
CommDelay=2
CommLogging=ON
ImageBackup=ON
ExitPrompt=ON

Initial Parameters-> Delay:3700 VCC:28 Glitch Type:B0/07 Timeout Factor:04

.................................................. ...................
................................................. !!!!!!!

******* Good response received! *********
55
===========================================
55 was hit at: Delay:3700 VCC:000B GlitchType:B0/07
Timeout Factor:03
Elapsed: 00:00:21
VCC Resolution: 0.25
Delay Range: 3700 to 3850
********************************

I have not seen Rom Master v1A posted on the forum?

I have not seen Rom Master v1A posted on the forum?

This is called hijacking a thread.

This thread is for posting results and discussion only.

You can find the Rom Master script here:

http://forums.dsstester.com/vbb/showthread.php?t=107314

Asking about the topic script is not thread jacking. There was no way to know, via search, that the thread containing the script was the RMv1A script (it does not say it in the title or text of the thread) so Thank You for posting the link.

:wacko:

Nice :D

Good job! Could you tell me which 4619's you used (I got 0619's)? My PS doesn't do anything above 30 ohms and, not much under!

RM1A and 385 or above.........you got balls son:o !!

Could you tell me which 4619's you used (I got 0619's)?

MAX4619CPE

Never heard of 0619's.

Oh, sorry for the confusion. On top of the chip it will say "MAX4619CPE(+)" just below and to the right it will have a production code/date i.e. 0619 means the 2006, 19th week. The reason that I ask is that the "MAX4619CSE(+)" 0612's are known to be bad. So I am wondering what kinda chips the more successful folks are using? But enough 'jackin'

I have a rom 103 rev 30b with a powersync 16 hours ago working and even does not open 220ohms 9v dip on any suggestion?

I have a rom 103 rev 30b with a powersync 16 hours ago working and even does not open 220ohms 9v dip on any suggestion?

Currently, Rev 30B is not unlockable unless the new RM_1C will open it.

If you do get into it with the new RM_1C which is in the files section, you will end up with unknown provider.

If, in effect I am using RM v1C it will wait for a couple of hours mas and if there is nothing will cancel it, probably later on it could open, thank you for the help

opened a rom 103 rev 300 with ohms at 190, not 190k. it took 4 minutes to pop the card. Now i cant get 2 rom 102 10b;s to pop at all with it.
i know its n the wrong thread. but i used a ps with a schotty diode. and flashed my atmel and it popped it. without changes any settings

Here is my settings from the last 10b's that I opened with my powersync. I opened 2 out of 3 third one looped. These take a long time to open I have had some run for over two hours, just don't look at the one that shows 5 minutes that card toke a lot longer it the ohms was reset many times.
chetsat

*USER SETTINGS*
ComPort=1
CommDelay=2
CommLogging=ON
ImageBackup=ON
ExitPrompt=ON

9 volt 500 ma power supply
Switch #1 and #7 on
Ohms 205 to 215

.................................................. ..................
.................................................. ...................
.......................................... !!!!!!!

******* Good response received! *********
55
===========================================
55 was hit at: Delay:00AF VCC:0017 GlitchType:B0/07
Timeout Factor:03
Elapsed: 00:05:34
VCC Resolution: 0.0625
Delay Range: 00AE to 00CE
********************************
* Rom102, Rev10B CAM OPEN! *
* PROCEED AS NORMAL *
* GOOD LUCK! :-) *
********************************


Parameters-> Delay:00BC VCC:0C Glitch Type:B0/07 Timeout Factor:04
Elapsed: 00:42:49

.................................................. ...................
.................................................. ...................
.................................................. ...................
.................................................. ...................
.................................................. ...................
.................................................. ...... !!!!!!!

******* Good response received! *********
55
===========================================
55 was hit at: Delay:00BC VCC:000F GlitchType:B0/07
Timeout Factor:04
Elapsed: 00:44:46
VCC Resolution: 0.0625
Delay Range: 00AE to 00CE
********************************
* Rom102, Rev10B CAM OPEN! *
* PROCEED AS NORMAL *
* GOOD LUCK! :-) *

opened a rom 103 rev 300...it took 4 minutes to pop the card.

legenda1a what settings did you use ? got a rom103 rev306 here

ComPort=1
CommDelay=?
CommLogging=?
ImageBackup=?
ExitPrompt=?

power supply,switchs,ohms ect.

Has anyone tried the higher revs like 30C yet? Just wondering...LOL!:beer:

pop a few 10b's with RM1a so far....great program!! thanks to the devolopers!

now i have 2 icams at rev 78a and i am on the fence to buy some BGA's and go for it or just trash a perfectly good 625 and 311? any success?-Josh

Hey, can you post how did you pop the 10bs? The settings, where did you get the script for the RM1a?

Hey, can you post how did you pop the 10bs? The settings, where did you get the script for the RM1a?

Check the Rom102 area there is a thread about unlocking Rom102 with the Powersync.

This thread is about unlocking Rom103s